ALBERTA AIR BRAKE PRACTICE TEST 01

Air brakes in Alberta, Canada are an essential component of highway safety. The province has strict regulations in place to ensure that all commercial vehicles comply with air brake standards.

Alberta Air Brake Test 01

1 / 25

Which of these has the ultimate responsibility to ensure their vehicle has safe, properly adjusted brakes before taking a vehicle out on the road?

The state inspectors

The owner

The driver

The mechanic

2 / 25

If a driver has permission to operate vehicles with air brakes, what endorsement will appear on their license?

3 / 25

If your air brake system is colour-coded, the secondary circuit components will be what colour?

Blue

Red

Yellow

Green

4 / 25

Atmospheric pressure at sea level is approximately what?

50 kPa

300 kPa

100 kPa

200 kPa

5 / 25

A vehicle travelling at 40 km/h will need how much more stopping power than a vehicle travelling at 20 km/h?

6 / 25

To perform an air brake inspection, the vehicle should be...?

Any of the above

On level ground

Facing slightly uphill

Facing slightly downhill

7 / 25

The lag time between an air brake being applied and the brake beginning to function is approximately...?

0.4 of a second

0.7 of a second

0.2 of a second

0.1 of a second

8 / 25

Brake components are constructed to withstand up to what temperature under hard braking?

200° C

250° C

150° C

300° C

9 / 25

One advantage that air brake systems have over hydraulic brake systems is that they are better able to tolerate what?

Abuse

Icy conditions

Wet roads

Small leaks

10 / 25

When a driver sees a problem, how long will they usually be between identifying the hazard and applying the brake?

0.75 of a second

2.5 seconds

1.5 seconds

0.25 of a second

11 / 25

What is the most common fault found with air brake systems during commercial vehicle inspections?

Leaking air lines

Worn out brake pads

Faulty compressors

Brakes out of adjustment

12 / 25

When removing fittings or hoses from an air brake system, you should make sure that the air pressure is...?

Drained

Steady

High

Moderate

13 / 25

When descending a long hill, you should apply the brakes...?

Continuously

Periodically

As little as possible

With a pumping motion

14 / 25

Brake fade occurs because the brakes are...?

Too wet

Too hot

Too cold

Too dry

15 / 25

A braking system works by converting the energy of motion into what?

Heat

Liquid

Friction

Gas

16 / 25

At what pressure in psi should the park control valve pop out?

30 - 55

15 - 20

20 - 45

55 - 75

17 / 25

To test for air system leaks, you should apply and firmly hold a full service brake application for two minutes. The system should not lose more than 4 psi, plus what additional losses per trailer?

4 psi

2 psi

1 psi

5 psi

18 / 25

How many different circuits are there in an air brake system?

19 / 25

If you are driving a truck and trailer combination of 20 m in length, you should allow how much following distance?

4 seconds

2 seconds

7 seconds

5 seconds

20 / 25

The first action in any air brake inspection should be what?

Turn on the ignition

Chock the wheels

Push the park control valve

Connect both air lines

21 / 25

A typical cylinder in an air brake system can generate a force of...?

3000 pounds

2000 pounds

1000 pounds

5000 pounds

22 / 25

When braking what should you do to prevent your vehicle jerking back?

Maintain an even brake pressure

Floor the brake pedal

Increase pressure on the brake pedal

Ease off the brake pedal

23 / 25

A tractor-trailer combination has accelerated to 100 km/h but now needs to make an emergency stop within seven seconds. The stopping force required will be approximately how many times more than the acceleration force?

24 / 25

To qualify for an air brake endorsement in Alberta, a driver must have had a minimum of how many hours of instruction (not including breaks)?

3.5

6.5

2.5

4.5

25 / 25

When testing the supply circuit, the compressor should be able to build from 50 to 90 psi within what time?

2 minutes

1 minute

3 minutes

5 minutes

Your score is

These regulations are designed to improve braking performance, reduce stopping distances, and prevent brake-related accidents. In Alberta, air brake certification is required for operators of commercial vehicles that use air brakes. In addition, drivers must complete a written air brake test and a practical skills test to obtain their certification. Failure to comply with these regulations can result in penalties or even the loss of driving privileges. With proper maintenance and regular inspections, air brakes in Alberta help maintain safe highways and prevent accidents on the road.

Drivingtest.ca has prepared this Air Brake practice test to assist drivers in understanding air brake systems. This practice test and practical instruction will assist drivers in operating air brake-equipped vehicles before and after obtaining their Alberta air brake endorsement.

To successfully prepare, consider utilizing these exams and the official Alberta “Air Brake Manual – A Guide for Students” to your advantage. The more knowledge you can attain, the better it will be for you once you decide to return to the license office to take the air brake license written knowledge test.